Ziwei road tiles

Don't confirm with the bricklayer about 10 before laying bricks!

You have to roll over! ! Must be reversed! ! Time consuming! Thanks a lot!

A, ceramic tile according to drawings or on-site typesetting:

For shaped tiles, it is necessary to make typesetting and typesetting on site, and the size or quantity can be adjusted to avoid pasting. If there is a problem with the back clearance, it must be reworked.

Precautions:

Tile typesetting should be considered comprehensively

Does the kitchen sanitary wall need to be stitched?

According to paper arrangement or on-site typesetting?

Hide small bricks and use a few millimeters cross card.

Typesetting should be done before laying bricks.

Do you want a threshold stone?

Do you want to spread it

How can we waste less tiles?

Second, the pressure wall or pressure wall:

Bricklayers usually do pressure walls by default, but if the owners prefer to press the walls, the consequences of poor communication in advance can be imagined.

Advantages: the pressure wall refers to the laying of wall tiles from bottom to top, and the laid tiles are not prone to hollowing.

Disadvantages: dust will appear for a long time. The naked eye can see that the gap between floor tiles and wall tiles is relatively large, which has a certain impact on waterproof function and is not very beautiful.

Advantages: the water on the wall will not flow into the gap to form stagnant water, the joint is small and more beautiful, easy to clean, and will not affect the waterproof function, and the gap will not become larger after a long time.

Disadvantages: paving is difficult, which tests the bricklayer's craftsmanship.

Three, dry shop, wet shop or plastic shop:

Many bricklayers choose wet paving to save trouble. If they don't make it clear in advance, the tiles will be empty in the later period and they can only admit that they are unlucky.

Dry paving: it can reduce the hollowing rate of ceramic tiles, and has low requirements for ground flatness, but high requirements for masons' craftsmanship.

Wet paving: the construction difficulty is low, but the tiles are easy to empty, which requires high ground flatness.

Glue paving: the tiles are pasted thin. After the tile is laid, its thickness is thinner than that of cement mortar, which requires a lot of special tile adhesive.

Four, chamfer, begonia Angle or corner protector:

Master usually does corner protectors by default. I don't know if I should chamfer the corners of begonia instead of sticking corner strips. If you feel ugly, you can only spend money to rework.

Chamfering: The technical requirements for craftsmen are very high. If it is not handled properly, it will easily lead to cracking and porcelain collapse, and the loss of tiles will also increase.

Begonia Angle: It belongs to the collision angle of 45 degrees, and the Begonia Angle should be 2-3 mm away from the glazed surface, so that the external angle is more beautiful and firm.

Glue shop: wrap this protruding outer corner with a corner protector. Cheap and money-saving, simple and fast construction but low value.

Five, pointing or beautiful seam:

In order to prevent the tiles from squeezing each other due to thermal expansion and contraction, the general master will leave a seam. We must communicate with the master to determine whether the tiles should be joined or stitched beautifully. How big is the gap between tiles? If you don't communicate with the bricklayer in advance and want to make beautiful joints, the tiles at home are too small to make beautiful joints. In this way, the tiles in the house are too big, and the tiles in the whole house may have to be repainted.

Precautions:

To make beautiful joints: the joint distance of tiles should be at least 1.5-2mm.

Don't make beautiful seams: The default seam distance for ordinary tiles is 1- 1.5mm (5mm should be reserved for matte tiles such as antique tiles).

Suggestion:

It is popular in the south to use large tiles as floor tiles or upper walls, which can be paved with dense joints or micro-joints. There are no cracks in the tiles after completion, so it is better to control them within1mm.

Six, do you want to soak in the water:

Be sure to tell the bricklayer what tiles you bought and whether you want to soak them in water. These all need to be made clear in advance to avoid rework later.

The water absorption of traditional ceramic tiles is too high to reach 10%, so it must be soaked in water when paving. If you don't soak in water, it will absorb the water in the cement mortar, which will lead to the tile falling off. The number of bricks needed should be calculated well, so as not to affect the return of the remaining bricks in the later period.

When laying ceramic tiles with water absorption less than 0.5%, there is no need to soak in water. On the contrary, soaking water will not absorb the moisture of cement mortar, which will lead to the instability of ceramic tiles.

Seven, using professional hole opener:

The tiles need to be perforated. If you don't use a professional punching machine to punch holes, it will cause cracks in the tiles and it will be very troublesome to replace them.

Eight, residual brick processing:

Be sure to tell the master what to do with the defective tiles before sticking them. If there is color difference or defect in the tile during construction, don't soak or lay it with water, just put it aside and inform you to deal with it. Otherwise, it is a defective brick, which will be reworked because of one or two bricks later, and it is not worth treating as a defective brick.

Nine, tell the teacher to mark the location of the water and electricity pipeline:

Be sure to remind the master to mark the location of the water and electricity pipeline with tape after pasting the wall tiles. When installing the bathroom and hardware in the later stage, it is necessary to punch holes in the wall tiles to avoid punching through the water pipes, and to avoid touching the water pipes in the later stage, causing the water pipes to break and leak.

Ten, floor drain mouth shop is stuck charges:

Communicate with the bricklayer in advance about the laying style of floor drain. At present, zigzag paving is still relatively mainstream, with simple shape, and the surrounding four tiles will make a slope in the direction of floor drain, which has fast drainage speed, is not easy to accumulate water, and is exquisite and practical.

Precautions:

There are also some network celebrities paving the way, with high face value and complicated seams. The master may increase the money. If you want to do it, you have to ask if you need to add money.