The tying method of the fishhook is a complete video.

1. Schematic diagram of hooking method

The method of hooking is explained. The Method of Hooking in Taiwan Province Fishing

How to hook in Taiwan Province fishing? Witkey flagship store (Tmall sells fishing gear) Xiaotian answers for you: You can also buy a 9.9 set meal with a hook tying device, and prepare a hook and a suitable fishing line. In order to ensure the shooting effect, I chose a bigger hook and a thicker fishing line.

In the actual hooking process, the length of the fishing line is determined according to the parting line length required by the fisherman himself. As shown in the figure, hold the hook in your left hand and bend the fishing line into a circle as shown in the figure. Pay attention to leave enough length at the ends of both sides.

Hold the right wire of the coil joint with your right hand and wind the fishing line on the hook handle. Note that the right thread end and hook handle should be wound together at the same time. 3. A * * * can be wound 4-5 times, not too much.

4. After winding enough times, turn the winding to the left hand for pinching, as shown in the figure, and then hold the thread end of the winding with the right hand to pull it out. 5. Pull it all the way to the back of your head and tighten it hard. At the same time, be careful not to push too hard and hurt your hand at the tip of the hook.

It is also important to make the direction of the fishing line drawn on the inside of the hook handle as shown in the figure, because the head fixing piece of the hook handle is inclined outward. If the fishing line is left on the outside of the hook handle, it will often cause the hook handle fixture to wear the fishing line, which will lead to the deviation of the fish.

6. Finally, subtract the extra thread with scissors. 7. As shown in the figure, the hook at one end of the sub-line is knotted, and the hook at the other end can also be used.

A diagram of how to tie a knot

There are many introductions about tying double hooks on the Internet.

This makes many fishermen not know which one to choose. Let me introduce a very simple and practical method. The double hooks made by this method are very neat and the fishing effect is excellent.

1, preparation tool: auxiliary line ruler (measuring auxiliary line length); Hook (generally recommended to use barb-free hook and barb-free new Kanto fishing); Scissors; Fishing line (mermaid, civilian military commander, Hua Er Daisiqiang are all very good); Sub-box (for placing the tied sub-wires, 40 cm-50 cm in length). 2. Measure the length of the parting line with a parting ruler. The parting ruler varies according to the fishing environment, and one side is 50-70 cm.

3. Next, tie the double hook. Note: (1) Leave a certain line length when tying the hook, and leave the same line length every time tying the hook (this will tie it neatly).

(2) When tying the hook, when winding the wire around the hook handle, it must be lightly wound (five or six times), and the wire can be blocked with fingers when slipping out. (3) When tightening the thread, slowly pull the thread end to minimize wear.

(4) This article is very important, which can avoid many broken lines. When taking up the line, the line should bypass the front of the hook handle, because the hook handle is inclined backwards. If the sub-line is behind the hook handle, it is easy to wear the sub-line when sliding the fish, resulting in tangency. 4, well, at this point, even if the double hook hits 3/4, it's still a little short.

Now tie the tied double hook. (1) Fixed hook distance, generally 1.5 to 3 hook distance. The selection of hook distance is not mentioned here. You can search online.

Insert two long needles into the sponge. Then hook the double hooks on the two pins respectively.

Then straighten the line and align it! (2) Good, so the hook distance is fixed. Next, take off the double hook, then tie the double strands, leaving a small circle at last. (3) The last step is to fix the double hook on the sub-box.

This is the level linked to practice. All virtues put filial piety first and fishing virtue first.

Explain how to tie a line and a fishing hook.

Hand fishing is generally single hook and double hook.

The thread used to tie the hook is called the brain thread, which is also the auxiliary thread. The distance from the hook handle to the lead pendant is called the brain line length.

Those hooked with nylon thread are called hard brain thread, and those hooked with nylon thread are called soft brain thread. Hard brain line is sensitive and suitable for fishing small fish.

The soft brain line is easy to bend and has strong expansibility, which is suitable for catching big fish. There are many ways to hook the brain thread, mainly by fastening the hook firmly, using scissors and small pliers when knotting, and avoiding knotting with hands and teeth.

The length of the brain line depends on the size of the fish. The fish brain line should be kept long, and when the hook is tied with soft brain line, it should be shorter than hard brain line.

The brain line is too long, and the fish has poor sensitivity when eating bait; The brain line is too short, and the lead pendant will touch the fish's mouth when the fish eats, which is easy to decouple. Hook method 1. Tie the thread on the hook shaft and make a big circle.

2. Wrap the fishing line and hook four or five times. 3. Finish putting back the outer ring.

4. Tighten and cut off the excess parts. 5. When tightening, pull the main line back to the hook tip. .

How to tie a hook

How to tie a hook

Hold the hook with your left hand and bend the fishing line into a circle, as shown in the figure. Pay attention to leave enough length at the ends of both sides.

Hold the right wire of the coil joint with your right hand and wind the fishing line on the hook handle. Note that the right thread end and hook handle should be wound together at the same time.

A * * * is wound 4-5 times, which should not be too much.

After winding enough times, turn the winding to the left hand to pinch it, as shown in the figure, and then hold the thread end on the right side of the winding and pull it out.

Pull it all the way to the back of your head and tighten it hard At the same time, be careful not to push too hard and hurt your hand at the tip of the hook. It is also important to make the direction of the fishing line drawn on the inside of the hook handle as shown in the figure, because the head fixing piece of the hook handle is inclined outward. If the fishing line is left on the outside of the hook handle, it will often cause the hook handle fixture to wear the fishing line, which will lead to the deviation of the fish.

Finally, use scissors to subtract the extra thread.

Illustration how to tie fishing line and fishing rod

When tying this thread, first put a space bean in the middle, and the space bean can slide in the middle. This method of tying fishing line and fishing rod is the most convenient.

The specific operation method of this knot is as follows: 1, pull the line back through the hook-eye live line; 2, wear into the lower part, pull the thread back to the upper part; 3. Continue to roll in circles and pull back the thread; 4, through the eye of a needle; Pull up with the first turn, and finally tighten; 6. Repair the basic knot of the unwanted thread: All fishing friends should learn how to tie a solid knot, because there are usually at least two knots and one connection on the fishing group. Precautions: Before knotting, wet it with water to reduce the friction that may hurt the fishing line.

When connecting the hook to the fishing line, be careful not to puncture your fingers with the tip of the hook. Trim all loose ends so that they don't get entangled with the fishing group.

The first headache for beginners in fishing is how to tie the hook, fishing line and fishing rod.