How to connect the network cable of Kyocera printer

How to set the standard edition of Kyocera 20 10 printer as a network printer, it is better to be detailed, thank you.

1, as shown in the figure, there are only two connecting wires on the back of the printer. This is the upper power cord, and this is the lower data cord. The ports connected to the printer are all fixed-shape sockets. You can tell which socket to plug in at a glance.

2. As shown in the figure, this is the port where the printer data cable is connected to the computer. Because it is a USB port, it can be directly plugged into the USB port at the back of the computer, which is the only channel for the printer to connect with the computer.

3. Connect the printer power supply, turn on the computer, and then turn on the printer. The round button in the picture is the power switch of the printer.

4. Insert the computer CD into the CD that comes with the printer, click "Quick Install" after the installation interface appears, and then click Next until the installation is completed.

5. After the installation is completed, there are three scanning shortcuts on the computer desktop, and the third "Scan into PDF file" is often used; You can see the printer name in the control panel, and you can view printer properties and other settings.

Find the IP address assigned by the local area network for this printer.

You can find the IP address assigned to this printer by the LAN on the print test page, which must be in the same network segment as the LAN. If it is not the same, you need to set it again and get the IP again. With this printer IP, you must install a printer program for each computer in the same LAN. It is correct to enter the IP address of this printer when necessary during the installation. This can realize that as long as the LAN is normal, every computer can print, and there is no need to print a server computer.

Printer is one of the output devices of computer, which is used to print the computer processing results on related media. There are three indicators to measure the quality of a printer: printing resolution, printing speed and noise.

How to install network printing for kyocerataskalfa20 10 printer?

First, share the printer on the computer connected to the printer, and then share it on other computers.

Double-click the shared printer, install the driver as prompted, and use it after success.

How to set up network printing for Kyocera pa2 100cx?

1 Start the web browser. Enter the IP address or host name of this machine in the address bar. You can check the IP address or host name of this machine on the status page. To print the status page, press and hold the [Start] key on the operation panel for 3 to 9 seconds. 3 Log in as an administrator. The factory default settings for initial users with administrator rights are as follows. * uppercase and lowercase letters (note case). Login User Name: Admin Login Password: Admin4 Click [TCP/IP] in the [Network Settings] menu. Configure the settings. 1 In TCP/IP-IPv4 settings (wired network), set [DHCP/BOOTP] and [Auto-IP] to [OFF]. 2 Configure [IP address] and [subnet mask]. 3 Configure [Default Gateway], [DNS Server], [WINS Server] and [Host Name] in "IPv4 Settings (Normal)" as required. 4 Click [Submit]. Important: After changing the settings, you must restart the network interface card. Turn off the power and then turn it on. You can also restart the network by clicking [Reset] in the [Management Settings] menu in the command center, and then clicking [Restart Network] in "Restart". Note: Please ask the IP address of the network administrator before configuring this setting. In the following cases, please set the IP address of DNS server through CommandCenter. When the host name is used, but the DHCP setting is set to Off. When a DNS server is used, but the IP address is not automatically assigned by DHCP. For detailed information about setting the IP address of DNS server, please refer to the following contents: CommandCenterRXUserGuide To restore the network settings to factory settings, press and hold the [Cancel] key and the [Silent Mode] key at the same time 15 seconds or more, and turn off the main power switch before turning it on.

How to connect a network printer directly with a network cable?

1. Click "Start" to select a network printer, and the computer will automatically search for printers in the local area network. If you can't find it. Click the printer I want, which is not in the list.

2. Click Browse to select the printer you need.

3. You can also enter an ip direct connection.

4. Mark the position in the diagram and enter the printer ip.

5. In the open window, select the printer to be connected, right-click it, install the driver, and you can add it successfully.

The fastest way to add a network printer:

1. Start-run, or open it with the shortcut key (win+R). In the run window, enter the printer ip directly.

2. Directly open the printer selection window, select the printer to be connected, and right-click to connect. Install the driver.