How to cut white hair?

Step 1: After copying the layer 1, enter the channel and observe the red, green and blue channels. It is found that the black-and-white contrast effect of the red channel is the most obvious, and the more obvious it is, the easier it is to pick it out, so choose it.

Step 2: Drag and drop the red channel onto the "Create New Channel" (with corner) icon below, or right-click and directly select "Copy Channel" to generate a copy of the red channel.

Step 3: Select Image-Calculate command.

Step 4: Pop up the calculation panel, and select "Overlay" or "Strong Light" mode in the mixed mode to make the black area darker and the white area whiter. Of course.

After the fifth step is confirmed, an Alpha channel will be generated (in short, when the selection is stored after calculation, Photoshop will convert part of the selection into white, and the rest into black, and put it into a new channel. Such channels are called alpha channels, which can make it easier and more accurate for us to choose the required options. If we don't choose once, we can calculate again to generate Alpha2, Alpha3, etc. , which will not be described here). White hair is the object we want to dig out, so we should get rid of white or gray other than white hair. On the premise that the foreground color is black, click the brush tool, the soft corner is 30 pixels, and the opacity is about 30%, and smear it on the extra white and gray areas to make it black and disappear. The upper right corner of the border with hair tips should be painted with a smaller brush, not stiff.

The sixth step is to enlarge the picture by n times when applying it to the hair tips.

Step 7: On the cheek, use a soft angle brush with pixels less than 10.

The eighth step is to wipe all around and clean the head. Click the curved double arrow icon of the thumbnail of the front background color below the toolbox on the left to replace the front background color. Press the shortcut key X, and the brush will turn white. Select 20 pixels, and the opacity is 100%. Apply it to your head as white.

Step nine. All right. Now it's time to choose the white-haired constituency. Click Select-Load Select command, and you will see the lovely ant line, which is the choice.

Step 10: Click on RGB and then click on the layer, return to the layer panel, and walk from the dark background to the bright foreground. Press Ctrl+J, the white hair will be pulled out, and a new layer will be generated, Layer 2.

Step 1 1 The white we cut out at this time is actually the gray at the hair tip. Put down the lower two floors and you'll find it. So we have to turn gray hair white. Press the shortcut key Ctrl+L to pop up the color scale panel (you can also use the curve tool), and pull the gray scale slider in the middle to the black slider, and you will see pure white hair immediately. Create a new blank layer (the "Create New Layer" icon below the Point Layers panel). Click the thumbnail of the foreground color, and the color selector panel will pop up. Click on a color at will to confirm. Then press Alt+Delete to fill the foreground color into the new layer.

Step 12 In the Layers panel, drag the layer 1 to the top and create a black mask for it (Alt+ Add layer mask button). You will see that the white hair is cut off to cut out the human face.

Creating a black mask Many friends will forget the most important step, which is to set the foreground color to black (just bend the double arrow or press the X key to replace it, and if the foreground color is not black, press the D key to restore it). Only in this way can the eraser tool be used normally. After the foreground color is black, click the eraser tool and use the soft (standard name or soft corner) eraser tool to erase the previous step on Layer 2.

Some dirty places exposed after using the color coding tool, such as the circle in the picture. Other places should also be cleaned. Then go back to the mask layer and smear it on the black block with a soft eraser of about 30 pixels and 40% opacity, gradually revealing the original skin color. The edge of the face should be enlarged n times as much as possible before it can be erased. Seeing a few friends who have handled well in other places, they are still not satisfied with their faces.

The last step is to adjust the background color. In Layer 3, press Ctrl+U to open the Hue/Saturation panel, select the Hue and Saturation tool, and drag at will to see that the background color is constantly changing.