How to weave a bracelet with a small rubber band

Question 1: How to weave a bracelet with small rubber bands? The materials, tools and steps required to prepare the step diagram are as follows. If you are satisfied with my reply, please accept it. Thank you!

Let's look at the materials and tools we need first.

The simple version of the tool is your own hand, and the material is colored rubber band+small hook for finishing.

The tool version uses a special tool that looks like a slingshot, crochet, colored rubber bands, and a small hook for finishing.

Next, step. Let's talk about the tool version first.

1. Wrap two around the figure 8 on the tool.

2. Turn the two ends of the lower 8 characters up and put them in the middle of the upper 8 characters, not the bracket.

3. Put the small hook for finishing on the rubber band turned up below, and then use it when finishing.

4. Stick a figure 8 on the tool with a rubber band.

5. At this time, turn both ends of the figure-eight rubber band in the lower layer onto the figure-eight rubber band in the upper layer, remove the tools and put them in the middle of the figure-eight rubber band in the upper layer.

6. Repeat this step until it is long enough.

7. Hook the last 8-shaped rubber band from the tool with a crochet needle and put it on the crochet needle.

8. With the aid of crochet, hang the last layer of rubber band on the free end of the small hook for finishing.

= = = = = = = = = I am the dividing line = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =

Without that special tool, you can only compile it by hand. The steps are as follows:

1. Hang the small hook on the rubber band.

2. As shown in the figure, put another rubber band on the first rubber band.

3. Continue to put it down until it is long enough. Pick out the part between the first rubber band and the second rubber band and hang it on the small hook. At the same time, put the folded end of a rubber band at the end of the hook, and it is finished.

'

Question 2: How to weave bracelets with small rubber bands? The materials, tools and steps required to prepare the step diagram are as follows:

Let's look at the materials and tools we need first.

The simple version of the tool is your own hand, and the material is colored rubber band+small hook for finishing.

The tool version uses a special tool that looks like a slingshot, crochet, colored rubber bands, and a small hook for finishing.

Next, step. Let's talk about the tool version first.

1. Wrap two around the figure 8 on the tool.

2. Turn the two ends of the lower 8 characters up and put them in the middle of the upper 8 characters, not the bracket.

3. Put the small hook for finishing on the rubber band turned up below, and then use it when finishing.

4. Stick a figure 8 on the tool with a rubber band.

5. At this time, turn both ends of the figure-eight rubber band in the lower layer onto the figure-eight rubber band in the upper layer, remove the tools and put them in the middle of the figure-eight rubber band in the upper layer.

6. Repeat this step until it is long enough.

7. Hook the last 8-shaped rubber band from the tool with a crochet needle and put it on the crochet needle.

8. With the aid of crochet, hang the last layer of rubber band on the free end of the small hook for finishing.

Question 3: How to use a small colored rubber band hook bracelet to make one set in half?

Question 4: How to weave bracelets with small rubber bands? You may be talking about rainbow weaving, which has just become popular recently. I recommend a book, Rainbow Weaving in One: 35 amazing rubber band bracelets and trinkets, which is the first book by a British craftsman imported from China. You can buy it online, which is cheaper than the bookstore.

Question 5: How to weave a bracelet with small colored rubber bands? There are many knitting techniques on the Internet, so you can check them online.

Question 6: The materials, tools and steps needed to graphically compile bracelets with rubber bands are as follows:

Let's look at the materials and tools we need first.

The simple version of the tool is your own hand, and the material is colored rubber band+small hook for finishing.

The tool version uses a special tool that looks like a slingshot, crochet, colored rubber bands, and a small hook for finishing.

Let's talk about the steps first. Let's talk about the tool version first.

1. Wrap two figures around the figure of eight on the tool.

2. Turn the two ends of the lower 8 characters up and put them in the middle of the upper 8 characters, not the bracket.

3. Put the small hook for finishing on the rubber band turned up below, and then use it when finishing.

4. Stick a figure 8 on the tool with a rubber band.

5. At this time, turn both ends of the figure-eight rubber band in the lower layer onto the figure-eight rubber band in the upper layer, remove the tools and put them in the middle of the figure-eight rubber band in the upper layer.

6. Repeat this step until it is long enough.

7. Hook the last 8-shaped rubber band on the tool with a crochet needle and put it on the crochet needle.

8. Hang the last rubber band on the free end of the small hook and arrange it with the help of crochet.

Without that special tool, you can only compile it by hand. The steps are as follows:

1. Hang the finishing hook on the rubber band.

2. As shown in the figure, put another rubber band on the first rubber band.

3. Keep putting it down until it is long enough. Pick out the part between the first rubber band and the second rubber band and hang it on the small hook. At the same time, put the folded end of the last rubber band on the idle end of the small hook, and it is finished.

Please refer to:

zuoye.baidu/...2

Question 7: How to wrap the first number 8 around the bracelet with a small colored rubber band, then put two flat ones to hook the first one to the third one, and then put one flat one to hook the third one, and then keep knitting like this.