24 methods of fancy shoelaces

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. Pass through the toe cap, and then respectively pass through the other two shoe holes.

3. Repeat this process until the shoelace passes through the two holes above. Evaluation: Is the traditional simplicity and comfort wrinkled? Note: It is a popular comfortable tying method, mainly because the cross part of shoelaces is just in the groove between the uppers on both sides, so it will not squeeze to the foot surface.

Second, the upper and lower system method:

1. Thread the toe cap directly from the bottom (gray part) and out from the top of each shoe hole.

2. The toe cap passes through the bottom, through the second pair of shoe holes from bottom to top, then through the top, and then inserted into the third pair of shoe holes.

3. Repeat this process until the shoelace passes through the two holes above.

Three, direct method (European) method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. One end of the shoelace (yellow end) goes out obliquely from bottom to top and directly enters another shoe hole in the second horizontal row.

3. The other end of the shoelace (blue end) diagonally passes through the third row of shoe holes from bottom to top, and goes straight into another shoe hole.

4, repeat the operation, two shoes alternately take the lead.

Four, direct binding method (lazy method):

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. One end (blue end) of the shoelace head extends upward from the top shoelace hole along the left side.

3. The other end of the shoelace (yellow end) directly passes through the hole on the right side of the second row.

4. The same end (yellow end) goes up and back through the remaining shoe hole.

Five, sawtooth method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. One end of the shoelace (yellow end) goes straight out along the right side and horizontally passes through the second row of shoe holes.

3. The other end of the shoelace (blue end) jumps over the second row of shoe holes, obliquely penetrates from below, and passes through the third row of shoe holes on the right.

4. Continue to push the two tool holder heads upward in pairs through the tool holder holes until one end (yellow head in the figure) passes through the top tool holder hole on the right.

5. The other end of the shoelace (the blue end in the legend) goes straight up along the left side and goes out from the top hole on the left side.

Six, shoe store system method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. The left end (blue end) of the shoelace is pulled obliquely to the right top hole.

3. The right end (yellow end) of the shoelace passes through the remaining shoe hole in zigzag.

Seven, rope ladder method:

1. Insert the toe cap from the bottom (gray part) through the two holes at the bottom.

2. Both ends of shoelaces are aligned upwards and pass through the second row of shoe holes.

3. Before threading the shoelaces upward into the next row of holes, cross-thread the shoelaces under the shoelaces on the other side in the vertical direction.

4. At the top hole, the two shoelaces cross again, pass under the vertical part, and then fasten.

Eight, double post-production method:

1. Thread the shoelaces directly through the holes in the second row above (gray part).

2. Cross the ends of shoelaces, skip the third row of shoe holes and enter the fourth row of shoe holes.

3. Continue downward and pass through two rows of shoe holes at the same time.

4. After passing through the bottom two shoe holes, pass through the spare shoe holes in pairs.

Nine, bow tie method:

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. Thread the shoelaces from the inside up (dotted line) to the next row of shoe holes, leaving a "gap".

3. After the toe cap passes through the top, it enters the next row of shoe holes.

4. Continue to wear upwards, straight inside and crossed above.

X. Hash system method:

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. Skip two rows of shoe holes and enter the fourth row of shoe holes after passing through.

3. Then, the two ends of the shoelace pass vertically downward through the third row of shoe holes.

4. Continue to wear upward, go up three rows after each crossing, and then come back and wear it out from the next row of shoe holes.