How to quickly make a 12-constellation bracelet _ How to make a 12-constellation bracelet?

How to weave bracelets with red ropes

Tools to be prepared for weaving red rope bracelets: red rope, about 1 m in length. Step 1: Fold the red rope in half and tie a button at one end. This is to facilitate the next step and prevent the red rope from running out. Pay attention to leave a buttonhole at the upper end when knitting, as shown in the figure.

Step 2: Draw three lines in the middle of the vertical axis in a cross shape. Step 3: weave a duplex at the lower end of the vertical shaft and fix it. All the next steps start with this knot.

Step 4: Pull down the double shafts and weave them with the rope below. Step 6: Straighten and tighten the braided rope.

Step 7: After weaving to a suitable length, cut off the thread ends and burn them, and weave the remaining two threads into a duplex. Step 8: Weave the remaining thread into one or two knots at most, thus completing the weaving of the red rope bracelet.

How to weave this red rope bracelet? Seek detailed steps

Two braids+snake knot+double+snake knot+double+Newbutton knot+double+double+snake knot+double+snake knot+double+two braids (with beads on them)+Newbutton knot.

It involves two braids, double braids, snake knots and double-line ox knots.

Two braids:

Double connection:

Snake knot:

Double knot:

If you can't read the picture, you can search the video online.

Weave a bracelet with a rope

I haven't found China knot rope for the time being.

And it's not clear on the phone. But you can still understand.

Ha ha. 1. Prepare a rope and fold two ropes in half (or two ropes). 2. Grab one end and put it on your leg or other place to rub the other end, and both will rub at the same time.

Pay attention to the winding direction of the wire itself. Don't twist it backwards.

3. When the right hand rubs one end, the other hand gently twists along the direction of the rope itself. Take your time, don't panic.

You can twist the rope piece by piece into what you want. Just find the right length and tie it.

4。 Looks like the fourth picture.

One end is annular, and the other end can be used for burning. It sounds difficult, but if you try, you will find it easy.

Although I really can't see how you made this bracelet, I think if I do it, I will divide it into two parts. One section is a rope that has been rubbed out.

Put it in the middle. The middle one is woven separately.

I'll do it. Of course, you can also start from the middle and do both sides.

Do you have your own method? Hehe o (∩ _ ∩) o.

How to weave a constellation bracelet?

That depends on what you want. Red rope bracelets I recommend six kinds of red ropes. The required material is No.25 embroidery thread, and 6 treaties 1 meter long embroidery thread is prepared.

Step 1: Choose your favorite color, as shown above: line A is red, line B is orange, line C is * *, line D is green, line E is blue, and line F is pink. Arrange six red ropes of different colors according to your favorite color, and glue them with transparent glue so that one end can't move. Step 2 of bracelet weaving: put the A line on the B line, and the first step of bracelet weaving begins. Step 2 of bracelet weaving: Line A wraps around Line B from top to bottom, and Step 4 of bracelet weaving: A wraps around Line B repeatedly 1 turn, and then tightens the second thread.

Step 5 of bracelet weaving: Next, the A line is wound around the C line twice, and then the double-line bracelet weaving is tightened. Step 6: Line A and Line D, Line E and Line F are circulated twice in the same order. Step 7 of bracelet weaving: Next, line B weaves the bracelet twice with line C, line D, line E, line F and line A in turn; Step 8: Layout of the third and fourth wires.

Knit to a suitable length, which depends on the size of each wrist. Cut off the extra thread at the end.

The threads at both ends can be braided into a colorful lucky red rope in three ways.

How to weave the knot of the red rope bracelet?

1. Ropes and accessories, made in Taiwan Province Province, bracelets and pendants, buttons made of red agate. 2. A hand rope with a length of 16cm was made, with an estimated length of 2m, including two in total.

3. Start knitting, center to the left and start buttonholes. The buttonholes are made of diamond knots, with agate diameter of 5mm and buttonhole length of less than 2 cm. 4. Circle the braided diamond knot. 5. Hold the buttonhole with a clip, which is convenient for weaving corn knots. 6. Then start knitting corn knots.

The corn knot is woven with four threads, and it is numbered here. 7.2 line pressure 1 line, 3 lines pressure 2 lines, 4 lines pressure 3 lines, 4 lines crossing 1 line.

8. Tighten. 9. The key to corn knots is to use the same force every time, so that they can be woven neatly and beautifully. Yes, 1 1. Taiwan Province province line is not very thick, but it is very thin. Look at the finished product. Source: Nvhong. com。

How to weave a bracelet with red rope

Red rope bracelet weaving, teach you to weave bracelets with red rope step by step.

Six kinds of red ropes for making bracelets.

The required material is No.25 embroidery thread, and 6 treaties 1 meter long embroidery thread is prepared.

Step 1: Choose your favorite color, as shown above: line A is red, line B is orange, line C is * *, line D is green, line E is blue, and line F is pink. Arrange six red ropes of different colors according to your favorite color, and glue them with transparent glue so that one end can't move. Step 2 of bracelet weaving: put the A line on the B line, and the first step of bracelet weaving begins.

Step 2 of bracelet weaving: Line A wraps around Line B from top to bottom, and Step 4 of bracelet weaving: A wraps around Line B again 1 time, and then tightens the second thread.

Step 5 of bracelet weaving: Next, the A line is wound around the C line twice, and then the double-line bracelet weaving is tightened. Step 6: Line A and Line D, Line E and Line F are circulated twice in the same order.

Step 7 of bracelet weaving: Next, line B weaves the bracelet twice with line C, line D, line E, line F and line A in turn; Step 8: Layout of the third and fourth wires.

Knit to a suitable length, which depends on the size of each wrist.

Cut off the extra thread at the end.

The threads at both ends can be woven in three ways.

A colorful lucky red rope is ready. The knitting method of the bracelet is so simple, why not try it yourself?

Description of bracelet weaving method

1, ready to use materials and tools;

2. Tie a knot on the black rope with a blue rope;

3. Then fix the black rope, and then use the blue rope to start winding the black rope, as shown in the figure;

4, winding to a suitable position, and tying the black rope;

5. A beautiful bracelet is finished.